GLOBAL TESTING & RESEARCH CENTER
TEST PROCEDURES & SAMPLE DESCRIPTION
|No.||Procedure||Scope of Test||Required Sample Quantity||Required Sample Particle Size||Comminution||Drying|
|1||Bulk density||Bulk density||–||–||mandatory||mandatory|
|2||Sieving||Particle size distribution||–||–||mandatory||mandatory|
|3||Point load test||Compression strength||30 - 50 particles||25 - 70 mm (typical Ø 50 mm)||mandatory||not applicable|
|4||UCS||Compression strength||30 - 50 particles||Cube of 50 or 70 mm edge length, alternatively drilling core (cylinder)||optional||not applicable|
|5||Wear disc test||Wear determination||5 - 10 particles||180 - 220 mm||optional||not applicable|
|6||HAZEMAG Abrasion test||Wear determination||4 x 400 g||12.5 - 19 mm||mandatory||not applicable|
|7||Chemical analysis||Chemical composition and free SiO2 content||500 g||< 150 mm||mandatory||mandatory|
|8||Rock texture analysis||Crushability forecast||3 particles||130 - 170 mm||optional||not applicable|
|9||Hardgrove Test||Grindability of coal||2 kg||≤ 100 mm||optional||not applicable|
|10||Laboratory impactor||Crushability and wear determination||40 kg||10 - 25 mm||mandatory||not applicable|
|11||Moistening and Drying||Determination of moisture content and saturation point||–||-||mandatory||mandatory|
|12||HAZEMAG adhesion measuring device||Determination of the potential of clogging of cohesive soils||–||Soils and clays only||optional||optional|
|13||■ Liquid Limit ■ Plastic Limit ■ Plasticity Index ■ Consistency Index||Determination of the potential of clogging of cohesive soils||–||Soils and clays only||optional||optional|
|14||Laboratory roll mill||Determination of crushability||20 kg||< 35 mm||optional||not applicable|
|15||Hammermill||Crushability, wear and energy requirement determination For grinding & drying: Remaining moisture content||2 Big Bags or 10 kg for quick test||< 45/50 mm Additional with hot gas generator for drying||optional||not applicable|
|16||HSI impactor||Crushability, wear and energy requirement determination||4 Big Bags||< 220 mm||optional||not applicable|
|17||HTI impactor||Crushability, wear and energy requirement determination||4 Big Bags||< 150 mm or < 70 mm for sand application||optional||not applicable|
|18||HRC / HCS||Crushability, wear and energy requirement determination||1 Big Bag or 20 particles for quick test||< 150 mm||optional||not applicable|
|19||HRD||Remaining moisture content, particle size distribution and energy requirement determination||5 - 6 Big Bags||≤ 100 mm||not applicable||mandatory|
A place for practical, application specific, raw material investigation. A program that helps establish valuable information specific to your project goals, material processing needs and the potential use of HAZEMAG equipment and services. It’s all about you: The HAZEMAG Customer!
It goes without saying that you are invited to accompany the tests in our Test Plant, which would in addition be a great opportunity to discuss your project in detail.
Behind the operation of every HAZEMAG product is found a wealth of experience, backed by a level of partnership and product support that remains second to none. Our application knowledge, equipment flexibility and market competitiveness puts us in a unique position to react to your precise project needs. We call it „Partnership Unlimited –the HAZEMAG Way“.
The existing plant facilities allow for the equipment to be combined and operated within the following groups:
■ laboratory testing
■ coarse crushing / sieving
■ fine crushing/grinding
■ grinding & drying
The machines in the plant are all from the current HAZEMAG range of equipment, to ensure that field conditions are replicated as close as possible.
The layout of the coarse crushing section has been designed to use one of the two impactors or the roll crusher. If a screen unit is used, oversize material can be returned to the feed material flow, i.e. operation in closed circuit.
The fine crushing and drying section with a hammer mill and a rapid dryer forms another core part of the test plant.
The hammer mill has been integrated into the system in such a way that a range of crushing/grinding & drying operations are possible.
In the section set aside solely for drying technology and the processing of wet feed materials is a rapid dryer, the feeding and discharge of which is effected by HAZEMAG rotary gate valves; the fine material is separated via cyclone and filter.
The whole plant is computer-controlled. There is a visual display of the current operational status of all units. A total of six basic menus are available, which can be modified as needed.
During the test process, the status of the individual equipment, such as the power input of the electric drives, the rotor tip speed of the crushers as well as the various system temperatures are displayed. Pre-programming of various parameters is also possible.
All the results from the tests carried out in the HAZEMAG Test Plant as well as any other special tests and investigations are evaluated in the test plant‘s own laboratory. Such tests are carried out to determine the following:
■ Plant capacity
■ Power requirements
■ Granulation curves
■ Wear rates
■ Thermal loads
■ Moisture contents
Such data forms the basis for the fulfilment of user requirements.
For specific detailed tests, a laboratory crusher, a laboratory roll mill, adhesion measuring device, liquid limit apparatus by Casagrande, HAZEMAG Abrasion test equipment according to the Pennsylvania Test method and a point load tester are available.
Feed materials (representative samples) for comminution or drying tests must be provided by the customer free of charge. Please refer to the table ‘Test procedures and sample description’ (see brochure) with regard to required quantities and sizes. For the test numbers 15-19, we require delivery in 1t Big Bags. Smaller quantities may be delivered in barrels or similar. Please feel free to contact HAZEMAG to discuss in detail the amount of test material that is needed for your specific project.
The test sample shall be identified with the following information:
■ Company name
■ Contact person
■ Phone number
■ Description of material (e.g. Limestone)
■ Identification (e.g. Project, Site, etc.)
Required raw material and process data:
■ Chemical and/or mineralogical analysis
■ Hardness and compressive strength of the feed material
■ Moisture content of the supplied material and (in the event of deviations) the humidity of the typical feed material
■ Source of the material
■ Your requirements for the product
■ Desired intended use and purpose
■ Safety data sheet of the material (if applicable)
HAZEMAG Systems GmbH
Global Testing and Research Center